AERO PLASTICS & SUPPLY CO.
CNC MACHINING & FABRICATION
Torlon®
Torlon ® is a high performance amorphous (non-crystalline) engineering thermoplastic. Chemically, Torlon ® is a polyamide-imide (PAI), a reaction product of trimellitic anhydride and aromatic diamines. It is called amide-imide because the polymer chain comprises amide linkages alternative with imide linkages. The combination of aromatic groups and imide linkages are responsible for the polymer's exceptional thermal stability. The amide groups impart flexibility and elongation, which results in an engineering plastic with exceptional toughness.
GENERAL PROPERTIES
Torlon ® is the highest performing melt processable plastic. It has superior resistance to elevated temperatures. It is capable of performing under severe stress conditions at continuous temperatures to 500°F (260°C). Parts machined from Torlon ® stock shapes provide greater compressive strength and higher impact resistance than most advanced engineering plastics. Its extremely low coefficient of linear thermal expansion and high creep resistance deliver excellent dimensional stability over its entire use range. Torlon ® is an amorphous material with a Tg (glass transition temperature) of 537°F (280°C).
TORLON ® GRADES
Torlon 4203 (Electrical Grade)
Torlon ® 4203 extruded PAI offers excellent compressive strength and the highest elongation of the Torlon ® grades. It also provides electrical insulation and exceptional impact strength. This grade is commonly used for electrical connectors and insulators due to its high dielectric strength.
Torlon 4301 (Bearing Grade)
Torlon ® 4301 extruded PAI is primarily used for wear and friction parts. It offers a very low expansion rate, low coefficient of friction and exhibits little or no slip-stick in use. Torlon ® 4301's flexural modulus of 1,000,000 psi is higher than most other advanced engineering plastics. This grade excels in severe service wear applications such as non- lubricated bearings, seals, bearing cages and reciprocating compressor parts.
Torlon 5530 (Glass-Reinforced Grade)
Torlon ® 5530 is 30% glass reinforced, compression molded PAI. It is ideal for higher load structural or electronic applications. This grade is similar in composition to Torlon ® 5030 PAI (injection molded). It is selected for larger shapes or when the greatest degree of dimensional control is required. Applications include burn-in sockets, gears, valve plates, impellers, rotors, terminal strips, and insulators.
|
TYPICAL PROPERTIES of TORLON® PAI |
||||
|
ASTM or UL test |
Property |
Torlon® 4203 |
Torlon® 4301 |
Torlon® 5530 |
|
PHYSICAL |
||||
|
D792 |
Density (lb/in³) |
0.051 |
0.052 |
0.059 |
|
D570 |
Water Absorption, 24 hrs (%) |
0.4 |
0.4 |
0.3 |
|
MECHANICAL |
||||
|
D638 |
Tensile Strength (psi) |
18,000 |
12,000 |
15,000 |
|
D638 |
Tensile Modulus (psi) |
600,000 |
800,000 |
900,000 |
|
D638 |
Tensile Elongation at Break (%) |
10 |
3 |
3 |
|
D790 |
Flexural Strength (psi) |
24,000 |
23,000 |
20,000 |
|
D790 |
Flexural Modulus (psi) |
600,000 |
800,000 |
900,000 |
|
D695 |
Compressive Strength (psi) |
24,000 |
22,000 |
27,000 |
|
D695 |
Compressive Modulus (psi) |
700,000 |
950,000 |
600,000 |
|
D785 |
Hardness, Rockwell |
E80(M120) |
E70(M106) |
E85(M125) |
|
D256 |
IZOD Notched Impact (ft-lb/in) |
2.0 |
0.8 |
0.7 |
|
THERMAL |
||||
|
D696 |
Coefficient of Linear Thermal Expansion |
1.7 |
1.4 |
2.6 |
|
D648 |
Heat Deflection Temp (°F / °C) |
|
|
|
|
D3418 |
Glass Transition Temp (°F / °C) |
527 / 275 |
527 / 275 |
527 / 275 |
|
- |
Max Operating Temp (°F / °C) |
500 / 260 |
500 / 260 |
500 / 260 |
|
C177 |
Thermal Conductivity |
|
|
|
|
UL94 |
Flammability Rating |
V-0 |
V-0 |
V-0 |
|
ELECTRICAL |
||||
|
D149 |
Dielectric Strength (V/mil) short time, 1/8" thick |
580 |
- |
700 |
|
D150 |
Dielectric Constant at 1 MHz |
4.2 |
6.0 |
6.3 |
|
D150 |
Dissipation Factor at 1 MHz |
0.026 |
0.037 |
0.022 |
|
D257 |
Volume Resistivity (ohm-cm)at 50% RH |
> 1016 |
> 1013 |
> 1013 |
NOTE: The information contained herein are typical values intended for reference and comparison purposes only. They should NOT be used as a basis for design specifications or quality control. Contact us for manufacturers' complete material property datasheets.
All values at 73°F (23°C) unless otherwise noted.
TORLON is a registered trademark of Solvay Advanced Polymers.
DURATRON is a registered trademark of Quadrant Engineering Plastic Products.
